Low Waste Bathrobe ================== .. figure:: bathrobe.jpg :align: center .. only:: html .. contents:: This is a simple bathrobe made out of fabric rectangles, shaped by a single pleat in the center back and a self-fabric belt. It is a pretty quick project (making it took me about half a day), but maybe not the best for beginner sewists, as inserting the sleeves can be a bit fiddly. I'm calling it low waste rather than no-waste because folding up the sleeves to make cuffs rather than cutting them down to the correct length (and having a leftover) sounds like cheating (and the pleat in the back is a *design choice*, but also a bit of cheating with regards to fabric waste). Materials --------- Fabric ^^^^^^ * Less than 2 m of towel material (see the pattern below for precise amounts); * 15 cm cotton jersey in a matching or contrasting color, for binding. The fabric should be both absorbent and somewhat elastic in all directions: honeycomb is a great choice, while terry may be a bit tricky to work with. Specifically, the sleeves and the end of the shoulder seam towards the neckline will require an elastic fabric; if not using one you can add small triangular gussets to ease the transition between the straight lines. Notions ^^^^^^^ * sewing thread to match the fabric. Pattern ------- Measurements ^^^^^^^^^^^^ You need to take the following measurements: ``height_neck_back_to_knee`` (A18) vertical distance from the back of the neck to the knee (or to where you want the bathrobe to end); ``across_back_b`` (I08) from armscye to armscye on the back; ``neck_back_to_waist_b`` (H19) vertical distance from the back of the neck to the waist; ``shoulder_length`` (I01) distance from the side of the neck to the tip of the shoulder; ``armscye_circ`` (L19) circumference around the armscye. Pattern ^^^^^^^ .. figure:: bathrobe.svg :align: center Measure a rectangle as wide as the full width of the fabric and as high as the desired length of the bathrobe (A18) plus 2 cm sewing allowance. Near the top, mark the quarter points, where you will cut the armscye slits, half ``armscye_circ`` (L19) long. From each quarter point, measure half ``across_back_b`` (I08) towards the center back, and measure the position of the center back seam, which should be ``neck_back_to_waist_b`` (H19) plus 2 cm long. Mark two slits, 5 cm tall for the belt in the pleat fabric, parallel to the seam at about 2 cm of distance, and aligned with the end of the seam. For the sleeves, measure two rectangles as tall as half the width of the fabric and as high as ``armscye_circ`` (L19) plus 4 cm allowance. For the belt, measure a rectangle as wide as the full width of the fabric, and 10 cm long. Instructions ------------ When sewing it's important to use a stretch stitch to preserve the elasticity of the fabric: if your machine has a lighting bolt stretch stich you can use that, otherwise a narrow zig-zag (1.5 mm wide) will do. Since all seams are fully enclosed (either french or flat-felled) a serger is not required, and using one will require adjustment of the pattern. Cutting ^^^^^^^ Cut the rectangles described in the Pattern section; mark the position of the armscye slits with a partial cut 5–10 cm long, but don't cut them fully until you're ready to insert the sleeves. .. tip:: As long as the selvedges aren't horribly different from the fabric, don't cut them away, but let them be part of the pattern pieces. From the jersey, cut cross-grain strips 4-5 cm wide for the binding; with wide jersey 3 strips will usually be enough. Slits ^^^^^^ .. figure:: 0101-marked_slit_facing.jpg :align: center From the binding, cut two rectangles 8-9 cm tall, mark a rectangle 1 cm wide and 5 cm tall in their middle and align them over the slits marked on the fabric, on the right side. .. figure:: 0102-sewn_slit_facing.jpg :align: center Sew over the rectangle, carefully cut the slit in the center, angling towards the corners. .. figure:: 0103-pinned_slit_facing.jpg :align: center Turn the binding to the wrong side, and topstitch at 1 cm from the slit to keep it in place. Pleat ^^^^^ .. figure:: 0202-basted_pleat.jpg :align: center Wrong sides together, sew the center back pleat. Baste the pleat flat near the top border. .. figure:: 0204-hanging_loop.jpg :align: center If you have scraps from straighening the fabric, cut a rectangle about 3 cm wide and 10 cm long, fold in in 3 and sew it in the middle with a wide zig-zag, otherwise you can use a bit of sturdy ribbon. Sew its short sides to the top border, near the center of the pleats. Shoulders ^^^^^^^^^ .. figure:: 0301-shoulders.jpg :align: center Wrong sides together, put the front over the back and sew ``shoulder_length`` (I01) starting from each sleeve slit with 8 mm allowance. .. figure:: 0302-shoulders.jpg :align: center Turn inside out, and sew again at 1 cm allowance to make a french seam. Sleeves ^^^^^^^ .. figure:: 0401-sleeves.jpg :align: center Wrong sides together, align one long side of the sleeve at 1 cm distance from the other, and sew with a 2 cm sewing allowance. Repeat with the other sleeve, taking care to do so simmetrically. .. figure:: 0402-felled_sleeve.jpg :align: center Fold the large allowances over the smaller one and topstitch to flat fell. Finish cutting the sleeve slits on the body. .. figure:: 0403-inserted_sleeve.jpg :align: center Wrong sides together, insert each sleeve in the body, pinning the sleeve seam at the bottom of the slit. Sew with a seam allowance of 8 mm, starting just before the bottom of the slit and ending just after it, so that there is a double line of sewing for strenght. .. figure:: 0404-french_sewn_sleeve.jpg :align: center Turn the sleeve inside out, sew again with a 1 cm allowance to finish the french seam, sewing again twice near the bottom of the slit. Finishing ^^^^^^^^^ .. figure:: 0501-binding.jpg :align: center Right sides together, sew the binding all around the edge of the bathrobe, starting from the center top. Also sew the remaining binding to the sleeve cuffs. Fold the binding over the edge, enclosing all raw edges, and hemstitch it by hand or topstitch it from the right side. Belt ^^^^ .. figure:: 0601-belt_sewn.jpg :align: center Fold the belt in half lengthwise, sew at 1 cm from the side. .. figure:: 0602-belt_finished.jpg :align: center Turn inside out; if you're using the selvedge of the fabric there will be no need to finish the ends. Gallery ------- .. figure:: bathrobe_back.jpg :align: center